TS100 B2 Lötkolben

CHF 69.00

NICHT am Lager

Kategorie:

Beschreibung

TS100 employs 304 stainless steel nested shell of Polycarbonate plastic. It  is designed with safety circuit and anti-static structure, integrated with DC5525 12-24V port, dual-temperature sensors and accelerated sensors with STM32 chip. Under these functionalities, temperature can be controlled accurately, stably and easily adjusted from 100°C to 400°C, and the TS100 also has sleep mode and automatic over-heating warning.

MAIN PARAMETERES

  • Power – 65W
  • Temperature stability – ±2%
  • Soldering tip resistance to GND – <2Ω
  • Temperature Range – 100℃ – 400℃(max)
  • Max operation ambient temperature – 40°C
  • OLED screen
  • Micro USB port
  • DC5525 port
  • Control part: length 96mm, Diameter:16.5mm
  • Heating part: Length: 72+33mm, Diameter: 5.5mm
  • Weight: 33g (power adaptor not included)
  • Compliant with EU certification: CE FCC

INCLUDES

  • 1 x TS100 Body
  • 1 x XT60 Stromkabel
  • 1 x B2 Tip
  • 1 x allen key
  • 2 x spare screws
  • Instructions Manual

 

Alternative Firmware

Die Ralin Firmware ist eine alternative open source Software für den TS100 die ihn um ein super Einstellungsmenü und ein paar intelligente Funktionen erweitert. Herunterladen könnt ihr die Software hier.

Die Installation ist denkbar einfach:

  • TS100 mit gedrückter vorderer Taste per USB an den Rechner anschliessen.
  • Das geladene .hex File auf den Kolbnen kopieren
  • Sobald das File kopiert ist startet der Lötkolben einmal neu
  • Wenn er wieder verbunden ist sollte das File die Endung „.RDY“ tragen.

Jetzt könnt ihr Euren Lötkolben wieder normal an den Strom anschliessen und die neuen Funktionen nutzen. Meine Highlights sind:

  • „Cutoff“ für Lipo: Ihr könnt einstellen was für einen Lipo (3S/4S usw) ihr dran habt und sehr ab sofort den Füllstand des Lipos im Display und der TS100 schaltet sich dann auch aus falls die Spannung zu niedrig ist.
  • Beim Abkühlen wird die Temperatur angezeigt und ihr wisst auf einen Blick wann der TS100 abgekühlt ist.

Die vollständige Feature Liste:

  • Soldering / Temperature control
  • Full PID iron temperature control
  • Automatic sleep with selectable sensitivity
  • Motion wake support
  • Settings menu
  • Set a voltage lower limit for Lithium batteries so you dont kill your battery pack. Please calibrate your input voltage first!
  • All settings saved
  • Improved readability Fonts
  • Use hardware features to improve reliability
  • Can disable movement detection if desired
  • Calibration of the temperature offset
  • Boost mode lets you temporarily change the temperature when soldering
  • Battery charge level indicatior if power source set to a lipo cell count.
  • Custom bootup logo support
  • Automatic LCD rotation based on orientation

Und die Beschreibung des Menüs:

  • PWRSC -> Power source, select a cell count if using a LiPo, or DC to disable the shutdown. (Sets it to minimum of 10V).
  • STMP -> The temperature the unit drops to in sleep mode
  • SLTME -> Sleep time, how long it takes before the unit goes to sleep
  • SHTME -> Shutdown Time, how long the unit will wait after movement before shutting down completely
  • MSENSE -> Motion Sensitivity,0*9,0 means motion sensing is turned off, 9 is most sensitive, 1 is least sensitive (ie takes more movement to trigger)
  • TMPUNIT -> Temperature unit, C or F
  • TMPRND -> Temperature Rounding, {1,5,10}
  • TMPSPD -> How fast the temperature should update in the soldering status screen.
  • DSPROT -> Display rotation mode, Automatic, Left handed or Right handed
  • BOOST -> Enable boost mode
  • BTMP -> Set the temperature for the boost mode
Menü