Logo DroneFactory
Produkt wurde deinem Warenkorb hinzugefügt.

SpeedyBee F405 Wing Mini Fixed Wing Flight Controller

SpeedyBee F405 Wing Mini Fixed Wing Flight Controller
SpeedyBee F405 Wing Mini Fixed Wing Flight Controller
SpeedyBee F405 Wing Mini Fixed Wing Flight Controller
SpeedyBee F405 Wing Mini Fixed Wing Flight Controller
SpeedyBee F405 Wing Mini Fixed Wing Flight Controller

CHF 39.90

nicht am lager

Voraussichtlich versandbereit ab 19. September 2026. Bei älteren Artikeln empfehlen wir, zusätzlich die aktuelle Nachfolgeversion im Shop zu prüfen.

Kategorie:

Specifications

SpeedyBee F405 WING MINI FC board

  • MCU: STM32F405, 168MHz, 1MB Flash
  • IMU(Gyro&Accelerometer): ICM-42688-P
  • Barometer: SPL006-001
  • OSD Chip: AT7456E
  • Blackbox: MicroSD Card Slot
  • UART: 6 sets (USART1, USART2, USART3, UART4, UART5, UART6 – Dedicated for Wireless board Telemetry connection)
  • I2C: 1x Used for magnetometer, digital airspeed sensor
  • ADC: 4x (VBAT, Current, Analog RSSI, Analog AirSpeed)
  • PWM: 12x (9x pin headers + 2x solder pads + 1x „LED“ pad)
  • ELRS/CRSF Receiver: Supported, connected to UART1
  • SBUS: Built-in inverter for SBUS input (UART2-RX)
  • LED: 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator (Red)
  • Analog RSSI: Supported, Named as „RS“
  • Dual Analog Camera Switching: Default to Camera1 Video Input (C1). Switch between C1 and C2 using ArduPilot Relay or INAV Modes/USER.
  • Both cameras should have the same video format, either PAL or NTSC.
  • Supported FC Firmware: INAV: SpeedyBeeF405WING (default) ArduPilot: SpeedyBeeF405WING
  • Weight: 5.6g

SpeedyBee F405 WING MINI PDB board

  • Input voltage range: 7~26V (2~6S LiPo)
  • Battery Voltage Sensor: Connect to FC board VBAT, 1K:10K (Scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)
  • Battery Current Sensor: 80A continuous, 150A peak Connect to FC board Current (Scale 195 in INAV, 50 A/V in ArduPilot)
  • TVS Protective diode: Yes
  • FC BEC output: Output 5.2V +/- 0.1V DC Continuous current 2 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed Sensor, Telemetry module
  • VTX & Camera power supply: The VTX power interface Vv offers two power supply options: direct battery voltage or integrated BEC 5V (sharing the 5V4A Servo BEC voltage)
  • By default, it is set to battery voltage
  • (Ensure the VTX and camera input voltage range is compatible)
  • Switching to 5V power supply is possible via pad jumper (using Servo BEC output)
  • (If using this method, ensure the current requirements for both servo and VTX are sufficient)
  • Servo BEC output: Output 5V +/- 0.1V DC Continuous current 4 Amps, 5A Peak Voltage adjustable, 5V Default, 6V via jumper Designed for Servos.
  • Weight: 5.5g

Ähnliche Produkte